MX-060 oven controlled crystal oscillator vectron international ? 267 lowell road, hudson, nh 03051 ? tel: 1-88-vectron-1 ? http://www.vectron.com ? sc-cut resonator ? frequency range: 5 mhz to 15 mhz ? low package height ? temperature stability to 0.4 ppb ? aging rate 0.1 ppb/day ? frequency range 5 to 20 mhz ? standard frequencies: 5, 10, 20 mhz ? lte, lte-a ? test and measurement equipment ? broadcast reference standard ? satcom terminals features applications MX-060 frequency stabilities 1 (stabilities listed for 10 mhz. for stabilities above 10 mhz values may degrade. please contact factory) parameter min typ max units condition vs. operating temperature range (refer - enced to +25c) -0.2 -0.4 -0.6 +0.2 +0.4 +0.6 ppb ppb ppb 0 +70c -20 +70c -40 +85c (+5v version) for better stability refer to the mx-042 datasheet. initial tolerance vs. supply voltage change vs. load change vs aging/ day vs aging/ day vs. aging / 1 year vs. aging / year (following years) vs. aging/ 10 years -50 -0.1 -0.1 -1 -0.06 -20 -10 -75 +50 +0.1 +0.1 +1 +0.06 +20 +10 +75 ppb ppb ppb ppb ppb ppb ppb ppb at time of shipment, nominal efc vs 5% load 5% after 24 hours of operation after 72 hours of operation after 72 hours of operation after 72 hours of operation retrace 2 -10 +10 ppb warm-up time 5 minutes to 10 ppb of fnal frequency (1 hour) @25c supply voltage (vs) supply voltage (standard) 4.75 5.0 5.25 vdc supply voltage (option) 11.4 12.0 12.6 vdc performance specifcations
performance specifcations vectron international ? 267 lowell road, hudson, nh 03051 ? tel: 1-88-vectron-1 ? http://www.vectron.com supply voltage (vs) parameter min typical max units condition supply voltage 4.75 5.0 5.25 vdc ordering code d 11.4 12.0 12.6 vdc ordering code b , temp stability t and j only power consumption eference voltage (vref ) - when specifed for custom units. 5.0 watts during warm-up, all temperatures 2.0 watts steady state @ +25c 4.0 watts steady state @ -40c 1.0 watts steady state @ +85c rf output start time 1 2 s time required to achieve 90% of amplitude signal [standard] hcmos load 15 pf signal level (vol) 0.5 vdc signal level (voh) 3.5 vdc duty cycle 45 55 % @ (voh-vol)/2 signal sine wave load 50 output power @ 5.0v,12 v +5 +7 +9 dbm harmonics -40 dbc subharmonics -40 dbc frequencies >= 10 mhz frequency tuning (efc) tuning range 150 250 ppb (fxed frequency option available) linearity 5 % tuning slope positive input impedance 100 kohm bandwidth modulation 150 hz control voltage range 0.0 2.5 5 vdc with vs=12.0v reference voltage output (vref ) the MX-060 can be confgured with a reference voltage on pin 2. this confguration requires a custom part number. please contact the factory for ordering information. reference voltage (vref ) - when specifed for custom units. 3.92 4.0 4.08 vdc with vs = 5.0 vdc 4.9 5 5.1 vdc with vs =12 vdc
additional parameters parameter min typical max units condition phase noise 3 -95 -125 -140 -145 -145 dbc/hz dbc/hz dbc/hz dbc/hz dbc/hz 1 hz 10 hz 100 hz 1 khz 10 khz @ 10mhz for lower phase noise, please review the ox-174 or ox-204 datasheet. allan deviation 3e-12 5e-12 1e-11 5e-11 1 s tau 10 s tau 100 s tau 1000 s tau @ 10mhz for oscillators with lower adev requirements. please review the ox-174 datasheet. for oscillators with tdev and mtie requirements. please review the ox-172 datasheet. g-sensitivity 1 ppb/g g-sensitivity of 0.5 ppb/g available in this package size. please contact factory for ordering information. for g-sensitivity <0.5 ppb/g, please review the ox-043 series. weight 55 g absolute maximum ratings 15.0 vdc output load 25 50 open pf ohms cmos sine operable temperature range -55 +95 c operable temperature range implies the device will continue to operate with no long- term damage to unit; however, it will not be specifcation compliant outside the operating temperature range. environmental and product classifcation shock (endurance) mil-std-202, method 213, condition j, 30g 11 ms sine vibration (endurance) mil-std-202, method 201 and 204, condition a, except 5g to 500 hz, 1 sweep each axis random vibration (endurance) mil-std-202, method 214, condition i-d humidity mil-std-202, method 103, condition b, 100% rh seal mil-std-202, method 112, condition d, hermetic, washable altitude mil-std-202, method 105, sea level to space resistance to soldering heat mil-std-202, method 210, condition a,b,c terminal strength mil-std-202, method 211, condition c (5 bends at 45 o , 2 lbs) moisture sensitive level 1 rohs 6 (fully compliant) storage temperature range -55 +125 c
type a code height h pin length l 0 14.55 7.5 pin connections 1 electronic frequency control (efc) 2 n/c optional reference voltage 3 rf output 4 ground (case) 5 supply voltage input (vs) dimensions in inches, [ ] in mm. outline drawing / enclosure vectron international ? 267 lowell road, hudson, nh 03051 ? tel: 1-88-vectron-1 ? http://www.vectron.com
ordering information mx - 060 0 - d a j - 400 1 - 10m0000000 product family mx: ocxo model 060 height 0: a14.55mm supply voltage b: 12 vdc d: 5 vdc stability code 109: 1ppb 800: 0.8ppb 600: 0.6ppb 400: 0.4ppb (temp codes t and j only) 200: 0.2ppb (temp code t only) frequency control 0:fixed frequency 1: electrical tuning (efc) vectron international ? 267 lowell road, hudson, nh 03051 ? tel: 1-88-vectron-1 ? http://www.vectron.com disclaimer vectron international reserves the right to make changes to the product(s) and or information contained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. rev: 3-11-2015 dmc for additional information, please contact rf output code a: hcmos e: sinewave temperature range e: -40c to +85c (supply voltage d only) d: -40c to +70c j: -20c to +70c t: 0c to +70c stability code - temperature and frequency options frequency 0 to +70 o c -20 to +70 o c -40 to +70 o c -40 to +85 o c (supply voltage d only) 5 to 10 mhz 200 400 600 600 > 10 mhz 400 600 800 109 frequency 5m00000000 10m0000000 20m0000000 (others available on request) vectron stocks the following items for small orders and prototype development: MX-0600-dee-6001-10m0000000 vectron stocks the following evaluation board for this product: ocxo evaluation board application notes: none additional ordering options available include custom heights, custom aging rates, custom temperature ranges, custom temperature stabilities, custom phase noise requirements, improved g-sensitivity, and oscillators with voltage reference output on pin 2. these modifcations require a custom dash number - please contact the factory for additional information. additional ordering options design tools notes: 1. unless otherwise stated, all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, and temperature (25c). 2. retrace defned as f1-fo where fo is the reading after the unit has been on power for 24 hours, and f1 is the frequency after 24 hours of followed by 60 minutes on. 3. phase noise degrades with increasing output frequency. 4. not all options and codes available at all frequencies. usa: vectron international 267 lowell road, suite 102 hudson, nh 03051 tel: 1.888.328.7661 fax: 1.888.329.8328 europe: vectron international landstrasse, d-74924 neckarbischofsheim, germany tel: +49 (0) 3328.4784.17 fax: +49 (0) 3328.4784.30 asia: vectron international 68 yin cheng road(c), 22nd floor one lujiazui pudong, shanghai 200120, china tel: +86 21 6194 6886 fax: +86 21 6194 6699
|
